TANK AND JET AGITATORS

Tank Agitator #36743

  • 3/4" NPT-M inlet

  • Increases tank liquid circulation by using the pump bypass liquid

  • Removal of end cap permits use in the horizontal position

  • Four interchangeable, color-coded agitator orifices to accomodate bypass flows of 2.9 to 6.5 GPM at 30 PSIG.

  • See performance chart below.

 

By using a #37382 agitator tee two agitators may be used for large tank installations which need additional liquid agitation (see drawing).

For jet and tank agitators:
Max rec. pressure: 125PSIG
Max. rec temp: 120o F

Jet Agitator #25467
for maximum agitation

  • Provides maximum agitation.
  • Variable spring-loaded orifice maintains constant velocity regardless of amount of liquid being bypassed.
  • 3/4" NPT-F inlet connects directly to bypass line and has a flow rate of 0-15 gallons per minute.
  • Venturies increase liquid volume 2-1/2 times, but are detachable for use in small tanks.
ORIFICE PRESSURE
PSIG 		INLET FLOW
GPM 		OUTLET
FLOW GPM
1/8 30 2.9 9.5
5/32 30 4.1 13.2
3/16 30 5.3 15.4
1/4 30 6.5 19.5

EIGHT-WAY MANIFOLD

Eight-Way Manifold #36516-3

  • Polypropylene

  • 3/4" NPT-F inlet, eight 1/2" NPT-F outlets and a 1/4" NPT-F outlet

  • Can be used on spray kits and some boom spraying systems

Part NO.

INLET
NPT-F 		OUTLET
NPT-F 		Pressure Range
PSIG BARS
36516 3/4" 1-2" 0-100 0-7

STRAINERS

Nylon Y-Type Strainers #29909 and 39911

  • Made of nylon with stainless steel screens and Viton O-rings.

  • A new coarse buttress thread is featured on the cap for ease in installation and removal. Only two turns and the cap is off.

  • Body configuration turns the liquid flow, the strainer acts as a plumbing elbow and plugs less due to internal flow design.

  • O-ring sits on a special chamber to seal against leaking and for easy removal of cap for cleaning.

  • Cap can be removed with the help of a slot in the cap. Use a screwdriver, etc. through the slot to loosen cap.

  • Strainer #39908 weighs approx. 9-1/2 oz.

  • Strainer #39911 weighs approx 1 lb., 7-1/2 oz.

Max. Recommended Pressure:
#39908 strainer (3/4" & 1"): 150 PSI
#39911 strainer (1-1/4" & 1-1/2") 75 PSI

Strainer
w/Screen 		Strainer liquid flow with 5PSI loss
Dela
Van 		Spray
Syst. 		Banjo McN
ally 		Hypro
3/4" with 40 mesh
screen 		30 GPM 23
GPM 		20
GPM 		17
GPM 		--
1-1/4" with 20 mesh
screen 		80 GPM 65 GPM 57 GPM 50 GPM 47 GPM
There is reduced pressure loss when compared to the competition.
Part No Inlet/Outlet
Pipe Size 		Screen Information
P/N of Screen Mesh Size of Openings Strainer Area Effective Straining
39908-3 3/4" 31500-3 20 .033" 22.4 in.2 10.3 in.2
39908-2 3/4" 31500-1 40 .018" 22.4 in.2 8.6 in.2
39908-1 3/4" 31500-4 80 .007" 22.4 in.2 7.1 in.2
39908-5 1" 31500-1 40 .018" 22.4 in.2 8.6 in.2
39908-4 1" 31500-4 80 .007" 22.4 in.2 7.1 in.2
39908-8 1" 31500-8 100 .005" 22.4 in.2 6.0 in.2
39911-1 1-1/2" 25157 20 .033" 51.0 in.2 23.5 in.2
39911-2 1-1/2" 25156 40 .018" 51.0 in.2.19.5 in.2
39911-3 1-1/2" 32878 10 .077" 51.0 in.2 30.2 in.2

Recirculating Y-type Line Strainer #50560

  • Made of nylon with stainless steel screens and chemical-resistant Viton o-ring

  • This strainer has been designed with a bypass outlet at the bottom of the screening area so that particles are flushed back to the spray tank. Less time is spent cleaning the strainer screen.

  • Body configuration turns the liquid flow. Strainer acts as a plumbing elbo.

  • The o-ring sits on a special chamber to seal against leaking and for easy removal of cap.

  • Approx. weight: 9-1/2 oz.

Max recommended Pressure: 150 PSI
Max recommended temp: 1200 F

Part # Pipe
Size 		Screen Information
P/N of
Screen Only 		Mesh Size of Openings Strainer
Area 		Effective Strain
Area
50560-2 3/4" 31500-1 40 .018" 22.4 in.2 8.6 in.2
50560-7 3/4" 31500-7 100 .005" 22.4 in.2 6.0 in.2
50560-6 1" 31500-3 20 .033" 22.4 in.2 10.3 in.2
50560-9 1" 31500-10 40/20 .018" 22.4 in.2 8.6 in.2